14 Common Misconceptions About Door Repairs > 자유게시판

Simple Door Repairs You Can Do Yourself

Your door is your primary barrier to water, dust bugs, heat. You can also control the amount of conditioned air which escapes your home through it.

Tiny dents and dings are simple to repair by applying spackle. It's inexpensive and easily available at any hardware store. It's also a good option, but may take longer to dry.

Repairing a Loose Handle

A damaged or loose door handle or knob could cause a lot of trouble and can even be risky, particularly for those who use their doors often. This problem can easily get worse with time and cheap double glazing could result in a costly repair or replacement in the future therefore it's essential to regularly inspect the handle to make sure it's secured.

Most door handles are held in place by a set of screws that secure the handle to the base. The screws can loosen over time for a number of reasons. They are most often loose because of normal wear and tear, but they can also come loose due to abrasions or moisture. Additionally, they can loosen from dirt and dust that accumulates in the hardware over time.

The first step is to determine which screws are loose. Depending on the kind of handle, this might be possible without removing the knob itself. There may be a slot inside the handle that allows you to insert the flathead, or a hole to hold a paperclip. If it doesn't, you will need to remove the rose to expose the inside screws. Once you have access to the base it's best to remove the knob and detach the base from the door.

Once the inner screws are exposed, you can tighten them using the same method that you used to loosen. Be sure to apply a tiny threadlocker should you require it for ensuring that the screws do not come loose again.

When the screws are tightened, reinstall the doorknob and handle by placing the base back into its place. It's a good idea to test the handle and observe how it performs before replacing any decorative faceplates or accessories. Examine the handle frequently to make sure it's in good working order. You might also want to apply a coat or polish to keep its appearance. If you have to apply polish or wax, do so with a soft, clean cloth. It is not advisable to apply anything that is rough, as it could damage the hardware.

Repairing a door that swings Open

If your door is swaying open when you close it, the problem could be that the latch isn't properly aligned with the strike plate hole inside the frame. This is a typical issue that can usually be solved with some simple steps. Family Handyman experts explain that you should first lean forward to check the gap between your frame and door. Often, this gap is caused by a hinge that isn't plumb, meaning it's not aligned with the other hinges, so that a straight line drawn across one of the pins would continue to the other.

In this case you'll need to loosen the hinge screw and move it slightly either forward or backwards to close the gap. Once you do this, it's also an ideal idea to tighten the other hinge screws to ensure everything is secured. After you've adjusted the hinges, you may need to move the strike plate's opening closer to the stop molding on the door jamb. If you've shifted your hinges, enlarged the strike plate's opening, or even moved the strikeplate itself, you will need to fill in any existing gap or screw holes by using a wood filler that matches the door frame.

If the above strategies don't work then you can also change the way you hang the door and install the hinge pins. If you need help get someone to hold the door in place to stop it from falling. To remove the hinge tap the pin's base the pin with an hammer, and then tilt the blade of a large flat-head screwdriver. The next step is to make sure that the hinges are shimmed in areas where there are swings or binds, starting at the bottom of the door and moving upwards to the top. You'll require a few shims at each spot and it's essential that the shims all made of the same material as the hinges themselves. After the shims are installed on the hinges, you can tighten them with hinge screws, and hopefully, your door will be closed!

Repairing the door that won't shut

If the door doesn't close properly, it's likely that it is rubbing against something in the frame. This may be a corner of the hinges or a component of the latch mechanism or a hole in the strike plate that is too small for the bolt that locks the door handle to reach and lock. You can often solve this issue by tightening hinge screws. If the door doesn't close, try loosening them a bit more and altering the hinges to make them a little more symmetrical to each other.

In certain situations, the latch may rub against the strike plate if the hole in the bolt is too big and does not match the strike plate's hole. Apply a strip of lipstick or another marking material on the latch to determine the location of the contact. When you open the door, check to see the area where the mark is placed. This will let you know if the latch is contacting the strike plate above or below.

You might be able to increase the size of the bolt pocket by moving the strikeplate a small amount. If that's not possible however, you can move the strike plate by using a screwdriver or hammer. Take off the screw that is holding the strike plate. Put the screwdriver's blade into the hole, then hammer the top of the plate using a Hammer. Repeat this process a few times until the strikeplate is exactly where you want it to be. Then screw it back into place.

If you've moved or increased the size of the strike plate or bolt pocket, you'll also have to fill in any existing screw holes. You may also need to patch any gaps above or below where the strike plate is now located. Wood filler that is in line with the color of your door's frame is ideal. Once you've completed this step the door should shut properly and stay shut. If it doesn't, you'll have to inspect the hinges for damage or looseness and replace any hinges that are damaged.

Repairing a door with leaks

If water leaks around your door, it's not just an inconvenience but also a serious issue for your home. The presence of puddles around your patio doors could indicate that your threshold or sill pan is damaged or the door was not installed properly, which can lead to extensive water damage and mold.

The best method to stop leaks is to replace old caulking. This will provide a solid seal against the elements, however over time it can crack and cheap double glazing peel leaving gaps that let water to get in. Use paintable and flexible sealants to ensure that they are able to endure weathering.

Then, examine the frame for indications of rot. This can occur in wood frames and double glazed front doors if not addressed immediately. If you discover rotting in the frame or door of a wooden wood, you'll need to remove it and make any necessary repairs. It's then a good idea to apply a stain or paint to the wood.

If you do not see any evidence of rot, it may be that air is leaking in around your door frame molding. Fill in the gaps with non-expanding caulking, gap filler rods or foam. You can use spackle to make a quick and Cheap Double Glazing repair.

While it's nice to fix your own home repairs whenever you can, certain projects are better left to professionals. It's best to have an expert replace your door when it's suffering from significant or extensive damage. This will save you money, and you'll have a door that will last for many years.

It is also important to consider whether your door is functional or attractively appealing. Begin by searching for the best door to fit your style and needs. This way, you can be sure that the door you choose will be a perfect choice for your home. Once you've decided to move forward, a professional can help with the installation process and ensure that your new door will appear its best.