Ten Things You've Learned In Kindergarden They'll Help You Understand Car Ignition Lock > 자유게시판

Why is My Car Ignition Locked?

There are many reasons your ignition could be stuck. The key might be dirty or have a broken wafer inside it. You can fix it by sliding the key in and out of the cylinder a few times.

The pins on the lock cylinder can also be stuck. You can tap the cylinder lightly using a small tack-hammer.

Check the Battery

The transmission shifter switch may be malfunctioning if the vehicle is in Park neutral, or doesn't start when the key is turned on. This can be easily fixed by moving the shifter up or down to put the car in the correct gear.

If it's not turning, the problem may be with the neutral safety switch or the transmission shifter cable. A mechanic or local auto locksmith can easily solve these issues.

The ignition cylinder could also wear out. Over time, the ignition and the key can wear out, causing them to become difficult to remove or insert. A lubricant such as silicon lock lubricant, could help solve this problem by allowing the wafers to slide into place.

The lint in your pocket and the adhesive from tape that holds packages together can also build over the key, preventing it from sliding into the ignition. You can clean the key using a cloth, or a cleaner such as Triflow, to solve this issue. You could also try a spare key to determine if the issue is the ignition or the key.

You could also tap the key with a small hammer, when it's in the ignition. This will cause a small vibration, which may be enough to loosen the wafers inside the ignition and allow them to slide into place. You should be careful not to scratch the ignition cylinder, or the key.

If all of the above options fail, it's likely to contact a locksmith or automotive mechanic to have it looked at. It could be that the key is broken inside the ignition or it could be the time to replace the entire thing. If the issue is with the key, a locksmith can create a new key for you. If the cylinder for the ignition is the problem then you'll need to take the car ignition replacement to a repair shop for it to be repaired. Luckily, these issues are generally easy to fix.

Check the Steering Wheel

A steering wheel that is locked can cause the ignition to stop turning. This occurs when the driver accidentally engages it as they exit or enter the vehicle. This is usually caused by pulling on the wheel while supporting themselves against it with their hands. It could also happen when someone in the rear seat is unable to stop the vehicle and engages the brakes when they get out of the vehicle.

This is a quick fix that doesn't involve a trip to the locksmith or mechanic. First, make sure that the gear shift is in Neutral or Park. If it's not, gently push or pull the gear shifter until it moves to one of these positions. Also, you should activate the handbrake or press the brake prior to turning the key.

If the wheel isn't locked, a quick look at the steering column will reveal whether the key is engaged with the lock. This is typically marked by a tiny "Lock" label on the lower part of the ignition circle. It is possible to disengage this by gently jiggling or pulling the key with moderate force. It is essential not to apply too much pressure, as it could damage the key, or break a wafer in the lock cylinder.

A spare key can be used to deactivate the lock. This may indicate that the original key has worn out and is no longer able to engage the wafers inside the lock cylinder. If this is the case, a professional at Karl Chevrolet Webster City will be able to make an alternative key.

If the new key does not engage, a short spray of oil that penetrates can assist. Simply spray a tiny amount around the ignition, and the keyhole that you have inserted, and then jiggle or tap it lightly until it starts to work. If this does not work you, you might need to seek out a specialist at your local car dealership. They can provide you with a new key and replace the ignition cylinder if needed.

Check the Key

If you are unable get your key to turn the ignition, it's likely that there is something wrong with your key. You can clean any foreign material (lint from packing tape or adhesive) from the key. You could also try rubbing alcohol on the key or Goo Gone to see if it helps.

If the pins inside the lock do not move in a proper manner when you insert your key, it's possible that they are stuck. You can test the spare key by gently sliding it out of the ignition once you have insert it. This should allow you to hear and feel if the internal lock pins move, which they ought to. If not, you can grease the pins using powdered graphite. You can buy graphite in small tubes that can be squirted into the keyhole. This should help the pins slide into position when you insert the key, and also prevent them from getting stuck.

A more serious issue is that it has become worn or damaged, making it unable to connect the internal pins in the ignition cylinder. This can cause the cylinder in the ignition to stop turning and prevent you from starting your vehicle. If this is the case you'll need bring your car ignition switch to a locksmith or repair shop for service.

If you can turn your car using an extra key, and you've ruled out any issues with the steering wheel or battery it could be because the ignition cylinder is been worn out. You can try to unlock the lock with the blunt screwdriver or handle of a small hammer. Don't use the head. A gentle tap on the cylinder will often free it and allow you to turn your key and start your vehicle. If this is not working then you'll need to replace the lock cylinder by a mechanic.

Check the Ignition Socket

The ignition socket is the place your key slides in and out of place when inserted. It is prone to getting blocked with debris, or simply wear and tear. You can inject some silicon lock lubricant in the ignition.

You can also employ a small hammer and very gently tap the inside of the ignition cylinder in an attempt to loosen or reset the pins that may be out of alignment. Be careful not to overdo this or you could cause significant damage to the ignition switch.

Before you try this, make sure that the gearbox of your car is in neutral or park. Many newer cars come with a system which locks the steering wheel when it is not in neutral or park. This can prevent the ignition key from being turned.

If you've tried all of these steps but your key is still unable to turn, it could be that the ignition housing needs to be replaced. Different vehicles have different procedures for replacing the ignition cylinder, so it is crucial to follow the correct procedures.

Generally, this means taking off the plastic cover that is over the steering column and ignition assembly. To remove this cover, you'll need to first adjust the tilt-wheel to the lowest setting and then loosen any fasteners that are holding it in place.

Once the cover has been removed, you'll have to take the old ignition cylinder from the steering column. It is then essential to check the new one that you have purchased with the original one to ensure that they're the same. After this step, you can install the new ignition cylinder in the same manner that you did with the old one.

It is possible that even with our best efforts, the ignition could be damaged and need to be replaced. It is recommended that if this happens, you contact an Tempe Locksmith. A locksmith can assist you in choosing the appropriate replacement and install it properly to ensure that your vehicle will be able to start up again.