10 Tell-Tale Symptoms You Need To Look For A New Patio Door Lock Repair > 자유게시판

Patio Door Lock Repairs

Over time, patio doors go through wear and tear that could lead to lock malfunctions. Fortunately, there are several easy and efficient steps that can help restore your uPVC patio door's security.

If it's resetting the lock or cleaning the mechanism for locking these simple fixes will help you make your home more secure.

Clean the Lock

Patio doors are ideal for letting the outdoors in and keeping out the elements. However, they can be a security threat when the lock isn't functioning correctly. Over time, wear and tear, cold and hot weather, dirt, and debris can cause your patio door lock to become difficult to operate. Fortunately, with a little maintenance, you can ensure your patio door's locks will always work effectively.

It's essential to clean your patio door's lock and all the moving parts. This helps to flush out any accumulated grime and coatings that may be preventing the lock from functioning in the way it should. Start by wiping all the moving parts on the lock for your patio door with a wet cloth. Then, use a scouring cloth or a rough damp cloth to scrub the dirt-infested areas of the frame and door. You should then wipe down the entire lock with dry cloths to eliminate any remaining dampness, and allow it to air dry before applying it to the next time.

If you have an outdoor door that has a pin tumbler latch mechanism it is possible to lubricate the lock by applying graphite powdered to the key or applying a Teflon-based lubricant such as WD-40 Multi-Use Product. This type of lubricant can be applied with ease and will not disintegrate over time. If you are unable to find the right lubricant for your needs You could try using a pencil with a thick tip. Put the pencil in the lock, then shake it around to spread the graphite.

Regular maintenance is also necessary to keep the tracks of sliding patio doors free from dust, dirt and other debris. These tracks are especially susceptible to snow and ice, which could cause them to jam or bind and make it difficult for your patio doors to open and close.

Tracks for sliding patio doors and rollers can be cleaned by removing any damaged or dirty weather stripping, cleaning them, then replacing it. The same can be done to patio door rollers which can be wiped down and then sprayed with a non-stick lubricant in order to allow them to move freely.

Lubricate the moving parts

uPVC french doors, like sliding patio doors, operate with 3-4 or occasionally five-point locking mechanisms, which include the lock cylinder and handle controlled by keys. These doors require maintenance, oiling of the moving parts. This can be done using a thin oil, but never WD40. This should be done every year, at a minimum.

If sagging hinges aren't a cause, the door may be misaligned and catching or rubbing against the strike plate's hole in the frame. Take off the strike plate and use a sharp tool to increase the size of its mortise. This will permit the latch to fit into the hole and also prevent it from rubbing against the frame.

While the cylinder is out of the way, measure its width with an object or a piece of wood patio door repair that will fit in the adjustment screw gap above the lock. The outer dimension is the distance from the outside of the door to the center of the cylinder, while the inner dimension extends from the center of the adjustment screw until the end of the cylinder.

Check the width of the lock.

If your patio door latch isn't able to turn, even after cleaning and lubricating, it's possible that it's not in alignment with the strike plate hole. Check if your door is properly balanced and if the hinge screws are in good condition. In a lot of cases, however, simply moving the strike plate downwards or upwards could fix the problem.

The latch might not work properly if the strike of the lock is not large enough. In this instance you'll have to increase the hole with either a hammer or chisel, and then test the latch to make sure that it contacts the strike plate in a smooth manner without rubbing against or landing on the door's frame jamb.

You should identify the type mortise lock that you have before purchasing a replacement. This can be done by looking at the faceplate and noting whether it is round or square. Take a look at each screw hole in the existing lock and note their dimensions. This will help you to locate the replacement lock that has the exact same width and will fit in the hole you have already.

You'll need to locate the mortise lock and inspect it for any scratches, bends, or other damage that requires to be repaired. A badly bent or damaged latch is more likely than one that's been used a lot to break. Replace the lock if it shows indications of damage.

Once you've inspected the lock and decided on the type of replacement you'll need then it's time to begin working on the actual repair. The spindle and handle must be removed from the doorway to the patio. Introduce the new handle. Start by putting in the handle inside by aligning it with the spindle, and then securing it in place by using the two screws or bolts that secure it. Once the handle in the interior is in, install the handle that is outside and screw it in place as well. After you've completed the steps, you can test the new handles to ensure they open and close easily and that the latch catches correctly when you strike the plate.

Check the door's Strike

The strike plate and door latch are two parts which work together to secure the door. A misaligned strike plate or door latch will result in the latch not being able to latch the door correctly. This issue is usually easy to fix.

Examine the holes that receive the strike plate to make sure they are clear of obstructions like dirt or plastic plugs. Then loosen the screws that secure the strike plate in place and allow it to move vertically but not separating it from the frame of your door. Then, you can adjust the strike plate until its holes for receiving align with the latch hooks on the door latch. Once the strike plate is adjusted, tighten the screws and test the door to determine whether it shuts easily with the new adjustment.

These plates are difficult to reach for homeowners who have sliding patio doors. However they are crucial to lock and unlock your door. The metal plates are situated on the top and bottom jambs of the door which are where they help support the latch. The door latch is inserted into this strike plate and creates the seal. If the strike plate is damaged or rusted or not properly installed the latch may not properly lock the door.

One of the most common reasons for the patio door lock to stick or not close is a misalignment between the latch and the strike plate. The easiest way to check for this is by performing the "lipstick test." Rub some lipstick along the edge of the deadbolt, and then apply masking tape over it. The lipstick will leave an impression when you shut the door. This will show you exactly where the latch connects to the strike plate. If the mark is too high or low, you can easily alter the strike plate.

If your patio door locks for sliding are not working properly they can help keep your home safe from burglars. You need to resolve this issue as quickly as you can. Follow these simple steps to fix your patio door lock and restore its functionality.